Presupported vs unsupported STL: when to redo supports

Presupported or unsupported STL files? What presupported files hold, what to check in a studio's supports, why scaling breaks them, and when to redo them.

Share

Presupported STL files (also written pre supported) are the parts of a garage kit figure with the studio's supports already added. Unsupported STL files are the raw parts, and you add every support yourself. Print presupported files at the studio's scale after a check in your slicer, and support the raw files yourself when you rescale or a check fails.

About three in four kits in my library come with presupports in some form. The rest, almost all from Chibi Station, come as raw STL files only. My library is the kits I have, not everything each studio offers, so a studio's other kits may come packaged differently. I slice in Lychee Slicer on a Mac and print on four Elegoo Saturn 3 Ultra printers, so this guide uses Lychee's names for things. Slicers change from one version to the next, so for the clicks themselves I link to Lychee's own guides and videos, which stay current.

In this guide

  • Presupported vs unsupported STL: which should you use?
  • What does presupported mean?
  • What the studios in my library ship
  • Checking a studio's supports before you print
  • When to print as supplied, and when to change the supports
  • Can you scale presupported files?
  • Do resin prints need supports?
  • Supporting a part yourself
  • Light, medium and heavy supports: marks against safety
  • Watch and read next
  • Sources

Presupported vs unsupported STL: which should you use?

Use presupported files when you print at the studio's scale and the part passes a check in your slicer. Use the raw files when you change the scale, when the part does not fit your plate as set up, or when the check fails.

  • What you get
    • Presupported STL files: Parts turned to a printing angle, with supports and usually a raft; often hollowed
    • Unsupported (raw) STL files: The bare parts, solid, as modeled
  • File formats
    • Presupported STL files: Supported STL files, Lychee scenes (.lys, .lyt) or a slicer project such as .chitubox
    • Unsupported (raw) STL files: STL files
  • Work before printing
    • Presupported STL files: Check each part in the slicer
    • Unsupported (raw) STL files: Turn, hollow, support and check each part
  • Control over supports
    • Presupported STL files: Editable in a Lychee scene; fixed in a supported STL file
    • Unsupported (raw) STL files: Every support is yours to place
  • Scaling
    • Presupported STL files: Print at the studio's scale only
    • Unsupported (raw) STL files: Scale first, then add supports at the new size
  • Use them when
    • Presupported STL files: Your scale and plate match the studio's setup, and the part passes the check
    • Unsupported (raw) STL files: You rescale, the part does not fit as set up, or the check fails

What does presupported mean?

Presupported means the studio has already turned a part to a printing angle and added supports. Most presupported parts also come with a raft, the flat base under the supports, and many come hollowed. Lychee describes presupported models as arriving with supports, orientation and hollowing already done by the person who prepared them.

Studios deliver presupports in three main forms. Some kits ship two or three forms side by side.

Supports built into the STL file

The most common form is a supported STL file. The studio exports the part, its supports and its raft as one STL file. The supports become part of the part's shape.

You can print a supported STL file as it is. You cannot select one support in it and move it, because the slicer sees one object. Lychee's manual support tools work on supports in a .lys or .lyt file. To change the supports on a supported STL file, go back to the raw STL file and support it yourself.

NomNom Figures names its supported files NOM_<part>_Supported.stl. Tanuki Figures ends its supported file names in _SUP. Lion Realm reuses the raw file names inside a separate presupport folder.

Lion Realm's Spike Spiegel shows the limit of the form. The full scene ships as supported STL files and one Scene.stl export, with no .lys scene to edit.

Lychee scenes (.lys and .lyt files)

A Lychee scene is the most useful form for a Lychee user. Lychee's documentation describes the two scene file types this way:

  • .lys: the file self-contains all the objects and the Lychee Slicer preparation work.
  • .lyt: the file holds only the preparation work. You must have the object files saved on your own computer.

Lychee notes that .lyt files suit studios that sell several sizes of the same kit. The studio shares its preparation work without repeating the object files in every size.

When you open a .lys or .lyt file, the supports open as Lychee supports. You can move a tip, delete a support or add one. That is the main reason to prefer a scene over a supported STL file.

To turn a .lys scene into an STL file, open the scene in Lychee and use Export 3D. Export 3D writes the hollowing, holes, supports and raft into the STL file. The exported supports are then fixed, like any supported STL file.

A .lyt file links to its STL files instead of storing them, so keep it in the folder the studio shipped it in, next to its STL files, and don't rename them. A .lys file stores the models inside it (Lychee's export page).

Can Lychee open CHITUBOX files?

Not directly, as of October 2026. Lychee's Import page lists the supported file formats as .lys, .lyt, .stl, .obj and .3mf. The .chitubox format is not on that list.

CHITUBOX is another resin slicer, and a .chitubox file is a CHITUBOX project. CHITUBOX's documentation describes .chitubox as its older project format, which holds model data and support data. Its newer project format, CHITUBOX Project File 2023, uses .ctp.

Every Moon Figures kit I have ships one presupported .chitubox project and no supported STL files. The Shionne kit, for example, ships stl/Shionne.chitubox. A Lychee user has two choices for a Moon Figures kit:

  1. Open the project in CHITUBOX Basic, the free version. CHITUBOX is one of the slicers Elegoo lists for the Saturn 3 Ultra.
  2. Support the raw STL files in Lychee.

CHITUBOX lists STL as a format it can import and export. For saving a supported model out of CHITUBOX Basic, see CHITUBOX's File menu documentation.

The Hybris 3D Studios kits I have ship several project formats beside their presupported STL files: .ags, .ctp, .chitubox and .3mf. The .chitubox and .ctp files are CHITUBOX projects, older and newer, and .3mf is on Lychee's import list. The .ags files each store one part's supports and hollowing.

Some studios also ship plate files made for one printer. NomNom Figures' Valrie kit includes sliced .chitubox plate files for Mars and Saturn printers. A plate file is laid out for that plate size and nothing else.

Hollowed or solid

Hollowing removes the solid inside of a part and leaves a wall. A hollow part uses less resin and weighs less, so it pulls less on its supports. Each studio decides which parts to hollow.

You can see a studio's hollowing by comparing volumes. My kit posts compare each raw STL file with its supported STL file. When the supported file holds less resin than the raw file, even with its supports added, the studio hollowed the part.

  • Tanuki Anya Forger chibi
    • Part: head → Head_SUP.stl
    • Studio's supported file, against the raw part: lighter, even with its supports
    • What it tells you: hollowed by the studio
  • NomNom Jiraiya
    • Part: gamaBodyE.stl → NOM_gamaBodyE_Supported.stl
    • Studio's supported file, against the raw part: lighter, even with its supports
    • What it tells you: hollowed by the studio
  • NomNom Jiraiya
    • Part: baseA.stl → its supported file
    • Studio's supported file, against the raw part: lighter, even with its supports
    • What it tells you: hollowed by the studio
  • Tanuki Vault Boy
    • Part: body
    • Studio's supported file, against the raw part: heavier
    • What it tells you: solid; the extra is supports and raft
  • NomNom Beelstarmon
    • Part: whole kit
    • Studio's supported file, against the raw part: heavier in total
    • What it tells you: the supports add more than any studio hollowing takes away

To read a file's volume yourself, and work out what a part takes in resin and what that costs, see how to estimate how much resin a print uses.

A hollow part needs drain holes, and the check below looks for them. A solid part needs no holes, but a large solid part pulls harder on its supports.

What the studios in my library ship

About three in four kits in my library come with presupports in some form, as of 5 October 2026. Most studios ship them as supported STL files. Moon Figures ships one presupported CHITUBOX project per kit instead. Chibi Station ships raw STL files only in nearly every kit.

Every kit post on this site has a Presupports line in its At a glance block. That line says what the folder holds, in which format, and where.

Formats by studio

This is what the kits I have from each studio usually hold. It isn't a full list of what each studio offers, and a studio's other kits may differ. A single kit can differ too, which is why the folder check below matters.

  • 3Dmoonn
    • What a kit usually holds: presupported STL files, with Lychee scenes or Lychee project files in most kits
    • Name cue: raw names use underscores; presupported names use spaces
  • Azerama
    • What a kit usually holds: supported STL files plus a CHITUBOX project
    • Name cue: none
  • Bee Figures
    • What a kit usually holds: presupported STL files plus a 3MF set
    • Name cue: STL_pressuported/ folder
  • Cepheus Studios
    • What a kit usually holds: presupported STL files under the raw names
    • Name cue: a separate presupported folder
  • Chibi Station
    • What a kit usually holds: raw STL files only
    • Name cue: none
  • Edythe Cross 3D
    • What a kit usually holds: raw STL files in most kits; a few add a CHITUBOX or Lychee file
    • Name cue: none
  • Hybris 3D Studios
    • What a kit usually holds: presupported STL files; some kits add .ags, CHITUBOX (.ctp, .chitubox) or 3MF projects
    • Name cue: presupport named in the folder
  • ilpaddyy
    • What a kit usually holds: presupported STL files
    • Name cue: none
  • Kabuki Figures
    • What a kit usually holds: presupported STL files plus one Lychee scene per part
    • Name cue: a Supported/ folder
  • Kaidan3D
    • What a kit usually holds: presupported STL files plus one Lychee scene per part
    • Name cue: none
  • Lion Realm
    • What a kit usually holds: presupported STL files under the raw names, with Lychee scenes or project files in most kits
    • Name cue: same names in a presupport folder
  • Moon Figures
    • What a kit usually holds: one CHITUBOX project per kit, no supported STL files
    • Name cue: stl/<Name>.chitubox
  • myAnimate
    • What a kit usually holds: supported STL files plus a CHITUBOX project
    • Name cue: a supported_ prefix
  • Neko Figurines 3D
    • What a kit usually holds: presupported STL files plus one Lychee scene per part
    • Name cue: none
  • NomNom Figures
    • What a kit usually holds: supported STL files plus one Lychee scene per part; some kits add CHITUBOX plate files for set printers
    • Name cue: NOM_<part>_Supported.stl
  • NYMPHA3D
    • What a kit usually holds: presupported STL files plus Lychee scenes
    • Name cue: none
  • PikkyPrints
    • What a kit usually holds: presupported STL files plus one Lychee scene per part
    • Name cue: none
  • Tanuki Figures
    • What a kit usually holds: _SUP STL files plus Lychee scenes; _MERGED uncut files for large printers
    • Name cue: _SUP at the end of the name

NomNom's Beelstarmon is a clean example of the NomNom pattern. The kit has 20 raw parts, 20 supported STL files and 20 .lys scenes. Every part has one of each.

Reading a kit folder

Studios name their presupported files in many ways. Most spellings contain "sup", so search a kit folder for "sup" first. These are the cues my kit posts have recorded:

  • _Supported in the file name (NomNom Figures).
  • _SUP at the end of the file name (Tanuki Figures, and some 3Dmoonn kits such as Tifa Lockhart).
  • A Supported/, presupported/ or Pre-Support/ folder holding files with the raw names (Kabuki Figures, Cepheus Studios, Lion Realm).
  • A supported_ prefix (myAnimate's Nami).
  • The studio's own spelling: Pressuported in a 3Dmoonn folder name and STL_pressuported/ from Bee Figures.
  • Spaces instead of underscores (presupported files in some 3Dmoonn kits).
  • Two support sets for one kit. Hybris 3D Studios' Velvet ships Option A files ending in _v1_.stl and Option B files with a leading __.

Then count. Match every raw part to a presupported twin. Gaps happen, and kit posts note them:

  • Tanuki's John Wick has presupports for all 22 split parts, but the _MERGED files have none.
  • Lion Realm's Thomas Andre has presupports for Pose 1. Pose 2 has them only for the parts it shares with Pose 1.
  • Cepheus Studios' Yor and Loid Forger has one raw file, base_full.stl, whose presupported version sits under a different name, uncut base/base.stl.
  • Kaidan3D's Lust has presupports for both split versions, but the one-piece figure is raw only.

How to organize STL files covers how to keep these folders in order.

Checking a studio's supports before you print

Open every presupported part in the slicer before you print it. Do this even for studios that print-test their kits. Tanuki Figures, for example, states that its models are print-tested. That test ran on the studio's printer, film and resin.

The check takes a few passes through the part. It looks at six things.

What to look at

  • Raft
    • How to see it in Lychee: 3D view from the side and from below
    • What you want: a flat raft inside the plate outline
    • Warning sign: the raft runs past the plate edge
  • Tilt angle
    • How to see it in Lychee: the part's size in the Scale panel, compared with the raw STL file
    • What you want: large flat faces meet the film at an angle
    • Warning sign: a large flat face lies parallel to the plate
  • Support density
    • How to see it in Lychee: 3D view, then the layer slider
    • What you want: supports under every low point and long edge
    • Warning sign: long bare edges, or one support holding a wide area
  • Tip size
    • How to see it in Lychee: click a support in a scene; zoom on a supported STL file
    • What you want: small tips on detail, bigger tips under heavy parts
    • Warning sign: tiny tips under a heavy hollow shell
  • Drain holes
    • How to see it in Lychee: look into the part with the layer slider
    • What you want: a hole into every hollow cavity
    • Warning sign: a hollow part with no hole
  • Islands
    • How to see it in Lychee: layer slider, then the Island Detector
    • What you want: every island touches a support
    • Warning sign: red regions in the Island Detector

Lychee's raft guidance gives a sense of normal: a raft thickness of 0.5 to 1.5 mm is enough in most cases.

Tilt shows up in the numbers. In Tanuki's Vault Boy, Body.stl is 49.7 × 89.0 × 65.0 mm raw. The studio's supported version measures 86.7 × 61.8 × 100.0 mm. The part is the same; the studio turned the part and lifted it on supports.

Support height shows up the same way. Vault Boy's base is a flat disc, 7.9 mm tall raw. The supported version is 26.5 mm tall, because the studio lifted the disc off the plate on supports instead of printing it flat.

Running the check in your slicer

The check is the same in any slicer. Open the studio's scene, or the supported STL file if there is no scene, with your own printer and resin selected. Look at the part from above and from below. Then step through it layer by layer from the bottom up, and stop wherever a region appears with nothing under it. That region is an island the studio's supports don't reach.

Lychee has an Island Detector that flags those regions for you, and a Suction Cup Detector for hollow parts. Its guides to the Island Detector, the Suction Cup Detector and the Slice View walk through each tool. Which tools come with the free edition changes from time to time, so check Lychee's pricing page. Stepping through the layers works in every version.

Not every island needs a support. Lychee's island guide advises leaving an island smaller than your lightest support tip alone, because a support that small can do more damage than the island.

If you change anything, save your own copy under a new name. Keep the studio's file as it shipped.

A kit worth a close check

Tanuki's Rock Lee is presupported for every part, and the studio hollowed the heavy pieces. The plinth quarters are large solid parts in the raw files, hollowed in the presupported files. They are hollow blocks with broad flat tile tops.

A hollow block with a flat face is where suction and trapped resin show up. Before slicing those quarters, check the drain holes and the tilt angle in Lychee.

When to print as supplied, and when to change the supports

Print as supplied when the part passes the check and your setup matches what the studio planned for. Change the supports when your printer, your resin or the part's size is different. A failed check is also a reason to change them.

  • The part passes every check in the list above.
  • You print at the studio's scale.
  • The part and its raft fit your build plate as the studio set them up.
  • Your printer is calibrated for the resin in your vat. The resin exposure test guide covers how.

Tanuki's Anya Forger chibi is a good candidate. The kit has three chunky parts, each with its own Lychee scene. All three fit a Mars-class plate, about 143 × 90 × 175 mm. The studio hollowed the head, and the one flat part, the base, is already tilted in the studio's scene.

A different printer

Plate size is the first difference. A Mars-class plate is about 143 × 90 × 175 mm, and a Saturn-class plate is about 219 × 123 × 250 mm. Studios set up some parts for one plate class and not the other. The guide to part sizes vs build plates measures two such cases: 3Dmoonn's Cindy Aurum base and Lion Realm's Yuki Tsukumo.

Turning a presupported part on its side to make it fit does not work. The supports would then point sideways, not toward the plate. Re-orient and re-support the raw STL file instead.

Film and lift speed are the second difference. The Saturn 3 Ultra ships with ACF release film, which Elegoo describes as a low-release-force design. Anycubic's troubleshooting guide notes that a higher lift speed can increase peel force. A studio's supports were built for its own printer's film and lift settings, not yours.

What size resin printer you need for figures covers plate classes.

A different resin

Each resin needs its own exposure time. Exposure time decides how fully each layer hardens, and that includes every support tip.

Tanuki Figures' listing for its Tifa kit says the download includes a Printing & Scale Guide with default settings for SunLu Standard resin. I tend to use Elegoo ABS-like resin. A different resin means the studio's tested settings no longer apply as written.

Anycubic lists insufficient exposure time as one cause of supports separating from a part. Its guide suggests raising exposure time by 0.5 to 1 second as a first test. Calibrate your exposure time for each new resin before you trust any supports, the studio's or yours.

After calibration, look again at the thinnest tips on the part. Best resin for anime figures and garage kits covers resin types.

A rescaled part

Any rescale beyond a small change means new supports. A supported STL file scales its supports with the part, and that changes every tip. The next section explains why and what to do instead.

A quick decision list

  • Situation: Same scale, fits your plate, passes every check
    • Print as supplied?: Yes
    • What to do: Slice and print
  • Situation: The layer slider or Island Detector shows unsupported regions
    • Print as supplied?: No
    • What to do: Add supports in a copy of the scene, or support the raw STL file
  • Situation: A hollow part with no drain holes
    • Print as supplied?: No
    • What to do: Add holes, or hollow the raw STL file yourself
  • Situation: The part or raft does not fit your plate as set up
    • Print as supplied?: No
    • What to do: Re-orient and re-support the raw STL file
  • Situation: Your resin differs from the studio's
    • Print as supplied?: Check first
    • What to do: Calibrate exposure time, then check the thinnest tips
  • Situation: You need a different size
    • Print as supplied?: No
    • What to do: Scale the raw STL file and support it at the new size
  • Situation: Only a .chitubox project, and you slice in Lychee
    • Print as supplied?: Check first
    • What to do: Open it in CHITUBOX, or support the raw STL files in Lychee

Can you scale presupported files?

Not reliably. Scale the raw STL files and support them again at the new size. Two of the studios in my library say so in their own words:

  • NomNom Figures, on its Neko Warrior Bust listing: "Please note that if you scale the model up or down, the pre-supports may no longer work reliably. While you are free to resize the model as you wish, support performance is only guaranteed at the original scale."
  • Tanuki Figures, in the Printing & Scale Guide.txt file in its Tifa Lockhart kit: "Never re-scale pre-supported files. Always use the no-support version if you wish to change scale."

Why supports scale badly

A supported STL file is one object. When you scale the file, every support scales with the part. The tips get thinner or thicker by the same percent as the part.

Here is what that does to J3D Tech's Light and Heavy tips and to support spacing. The tip values come from the preset list further down. The spacing line starts from the 2 mm gap Lychee's Manual Supports guide suggests for the bottom layers.

  • Scale: 50%
    • Light tip (0.3 mm at 100%): 0.15 mm
    • Heavy tip (0.6 mm at 100%): 0.30 mm
    • Light shaft (1.1 mm at 100%): 0.55 mm
    • Spacing (2 mm at 100%): 1.0 mm
  • Scale: 75%
    • Light tip (0.3 mm at 100%): 0.23 mm
    • Heavy tip (0.6 mm at 100%): 0.45 mm
    • Light shaft (1.1 mm at 100%): 0.83 mm
    • Spacing (2 mm at 100%): 1.5 mm
  • Scale: 125%
    • Light tip (0.3 mm at 100%): 0.38 mm
    • Heavy tip (0.6 mm at 100%): 0.75 mm
    • Light shaft (1.1 mm at 100%): 1.38 mm
    • Spacing (2 mm at 100%): 2.5 mm
  • Scale: 150%
    • Light tip (0.3 mm at 100%): 0.45 mm
    • Heavy tip (0.6 mm at 100%): 0.90 mm
    • Light shaft (1.1 mm at 100%): 1.65 mm
    • Spacing (2 mm at 100%): 3.0 mm
  • Scale: 200%
    • Light tip (0.3 mm at 100%): 0.60 mm
    • Heavy tip (0.6 mm at 100%): 1.20 mm
    • Light shaft (1.1 mm at 100%): 2.20 mm
    • Spacing (2 mm at 100%): 4.0 mm

Scaling down makes the tips thinner. At 50%, a Light tip is 0.15 mm, thinner than J3D Tech's 0.24 mm Ultralight tip. Lychee warns that a tip that is too small risks support failure.

Scaling up makes the tips thicker, so the marks get bigger. A Heavy tip at 200% is 1.2 mm across. Spacing grows too, so gaps open between supports. A curve that was well supported at 2 mm spacing now has 4 mm gaps.

What scaling does to the load

A part's size changes three things at different rates.

  • Length changes by the scale factor.
  • Area changes by the scale factor squared. That includes each layer's area and each tip's contact area.
  • Volume and weight change by the scale factor cubed.

At 150%, each layer has 2.25 times the area (1.5 × 1.5). The part holds 3.375 times the resin (1.5 × 1.5 × 1.5). Each tip's contact area grows 2.25 times, the same as the layers.

So the weight each square millimetre of tip has to hold rises by 1.5 times (3.375 ÷ 2.25). At 200%, it doubles (8 ÷ 4). Peel force also grows with the area of each layer, as Liqcreate's guide to peel forces explains, so the pull on each lift grows as well.

A scaled-up supported STL file has the same number of supports as the original. Each support now holds more weight against more peel force. Scaling up is how a part that printed well for the studio can fall off its supports for you.

What Lychee says about scaling supports

In a .lys scene, the supports are Lychee supports, separate from the object. Lychee's documentation says Recalculate Supports can help if you need to slightly rotate or scale an object. It also warns that if you rotate or scale too much, you will need to redo all the supports or risk print failure.

Lychee covers what scaling does to presupported models in its video Q&A with Lychee Slicer: Scaling Pre-Supported 3D Models.

Printing a kit at a different scale

Start from the raw STL files, not the supported ones. Scale every part of the kit by the same percent, with uniform scaling on, so the joins still fit. Then check plate fit, turn, hollow and support each part at its new size, and run the island check again. Lychee's Scale page shows where the settings are, and its video You need to do this before scaling down a model covers the step people most often skip.

The guide to part sizes vs build plates covers plate fit at the new size.

Do resin prints need supports?

Yes, almost every part does. A resin printer builds each part upside down, one layer at a time, and each new layer hangs from the layers already printed. Supports give a new layer something to hang from when the part itself does not.

Every layer hangs from the build plate

The Saturn 3 Ultra is an MSLA printer, the kind that hardens resin with UV light shining through a screen. The build plate lowers into the vat. A thin layer of resin sits between the plate and the release film (FEP) at the bottom of the vat. On the Saturn 3 Ultra, that film is an ACF film.

UV light from the screen hardens the thin layer. The plate then lifts, and the new layer pulls away from the film. Resin flows back in, the plate lowers, and the next layer hardens under the last one.

The first layers stick to the build plate. Every layer after that hangs from the layer above it.

In the slicer, the view is flipped back to normal. The build plate is at the bottom of the screen, and the part grows upward. "Lowest point" in this guide means lowest in the slicer view.

What are islands in resin printing?

An island is a region that starts printing with nothing to hang from. Lychee's documentation defines an island as any part of a model not connected to the rest until later in the print. It also counts the first layer of any part that does not touch the build plate.

In the slicer view, an island is any point lower than everything around it. A chin, a fingertip, the lowest end of a hair lock and the tip of a sword can all be islands. Which ones are islands depends on how the part is turned.

Without a support, an island's first layer hardens onto the film with nothing above it. When the plate lifts, that layer stays stuck to the film or drops into the vat. The rest of the feature then prints in the wrong place or not at all.

An overhang is a surface that leans out past the layers above it. A cape edge, an outstretched arm or the brim of a hat can overhang. Formlabs lists overhangs, spans and unsupported minima as the features that need supports, and "minima" is its word for islands.

Formlabs also lists what too few supports cause. Layers misalign, the part pulls off its raft, and thin features warp. In the worst case, a flat hardened layer is left on the bottom of the vat.

The pull on every lift

Every lift peels the newest layer off the film, and cupped or hollow shapes add suction to that pull. How to hollow resin prints covers peel force, suction, orientation and drain holes. Supports carry that pull and the part's weight on every layer, so build them for the worst layer, not the average one.

Supporting a part yourself

Supporting a part yourself follows a fixed order. Start from the raw STL file, turn and hollow it, add automatic supports, then fix the islands and fine tips by hand.

Start from the raw STL file

Chibi Station's Frieza is a full example of a raw kit. Chibi Station ships the kit as raw STL files only, so you support all 24 parts yourself.

Plate fit is not the hard part. All 24 parts fit a Mars-class plate, and the largest, head.stl, is 96.9 × 53.9 × 40.5 mm.

The thin parts are the hard part. The four water pieces are wavy sheets with pointed tips. water4.stl is a thin sheet spread across an 81.3 × 29.6 × 61.6 mm box. The five trees are round crowns on thin stalks, and the smallest, tree3.stl, is tiny. The energy ball, power.stl, is 9 mm across, and the two arm gems are tiny too.

The raw files are also solid. Heavy solid parts need hollowing and drain holes before they get supports.

A kit like that is a lot of support work. If you would rather start with printed parts, the shop sells printed, unpainted kits, with US shipping only.

Turn and hollow the part first

Turn the part before you add supports, because orientation decides where the islands fall and supports land on the side facing the plate. Hollow heavy solid parts and add drain holes first, as how to hollow resin prints explains.

Automatic supports as a start

Most slicers can add supports for you. In Lychee, Auto Supports places supports on islands and overhangs using a preset you pick. Treat what it places as a first draft. Run the same check you would run on a studio's file, then fix what the check finds.

Support settings: tip diameter, length and shaft

Lychee's free version has three support presets: Light, Medium and Heavy. Each preset sets three values:

  • Tip diameter: the size of the point that touches the part.
  • Tip length: the length from the main shaft to the end of the tip.
  • Diameter: the thickness of the shaft from the base to the tip.

Lychee's documentation hosts J3D Tech's guide to resin printing, which gives starting values for each preset. These are J3D Tech's recommended values, not Lychee's defaults.

  • Preset (J3D Tech's values): Light
    • Tip diameter: 0.3 mm
    • Tip length: 2.5 mm
    • Shaft diameter: 1.1 mm
  • Preset (J3D Tech's values): Medium
    • Tip diameter: 0.4 mm
    • Tip length: 2.5 mm
    • Shaft diameter: 1.3 mm
  • Preset (J3D Tech's values): Heavy
    • Tip diameter: 0.6 mm
    • Tip length: 2.5 mm
    • Shaft diameter: 1.5 mm

The same guide gives values for the extra presets in Lychee's paid edition, such as Ultralight at a 0.24 mm tip. Lychee's Support Presets page shows how to set your own.

Support tips, contact depth and break points

The tip is where a support meets the part. Lychee's support components page describes the trade-off plainly. A larger tip diameter holds harder but leaves a bigger mark. A tip that is too small risks the support failing.

Contact depth is how far the tip goes into the part. A deeper contact holds better and leaves a deeper mark to sand.

A break point is a ball at the end of the support, larger than the tip. When you snap the support off, the break happens there instead of in the part, which makes cleanup easier.

The raft

The raft is the flat base under the supports. Keep it within the thickness range in the check above. A bigger raft is not always safer: Lychee's raft guide notes that more raft area means larger layers, which raises the risk of layers separating.

Fixing islands and fine tips by hand

Manual supports fix what the automatic pass missed. Work from heavy to fine. Put sturdy supports on the lowest islands first, then the large features like hands, weapons and capes, then light supports on small islands and fine detail. Run the island check after each round.

J3D Tech sorts supports into four jobs, in this order:

  1. Structural: holds the part to the build plate.
  2. Shape: keeps the part in its shape.
  3. Detail: the smallest tips, for small islands.
  4. Bracing: keeps anything from shifting side to side during the print.

For small islands and thin parts like Frieza's tree stalks, Lychee recommends light supports and Mini supports, which have a tip at each end. Lychee's Manual Supports guide covers placing, moving and adjusting supports, and its video Learn how to support fast a full figurine shows the whole process on a figure.

Save your work

Save the finished part as a .lys scene, which keeps the part and your preparation work together, and keep the raw STL files untouched beside it.

Light, medium and heavy supports: marks against safety

Every support leaves a mark, and a bigger tip leaves a bigger mark. Heavier supports make a failed print less likely. Choosing a support size is a trade between cleanup and safety.

Formlabs states the trade in one line: adding more supports increases the likelihood of print success, but also adds post-processing work. Its advanced settings guide adds that a smaller touchpoint needs more density to hold the same part. Touchpoint is Formlabs' word for a support tip.

Mark size by preset

A tip mark is roughly a circle the size of the tip. Its area is π × (tip diameter ÷ 2)². A larger contact area also holds harder, so the same number describes both the mark and the hold.

  • Preset (J3D Tech's values): Ultralight (paid version)
    • Tip diameter: 0.24 mm
    • Contact area per tip: 0.045 mm²
    • Compared with Light: 0.64 times
  • Preset (J3D Tech's values): Light
    • Tip diameter: 0.30 mm
    • Contact area per tip: 0.071 mm²
    • Compared with Light: 1 time
  • Preset (J3D Tech's values): Medium-light (paid version)
    • Tip diameter: 0.35 mm
    • Contact area per tip: 0.096 mm²
    • Compared with Light: 1.36 times
  • Preset (J3D Tech's values): Medium
    • Tip diameter: 0.40 mm
    • Contact area per tip: 0.126 mm²
    • Compared with Light: 1.78 times
  • Preset (J3D Tech's values): Heavy
    • Tip diameter: 0.60 mm
    • Contact area per tip: 0.283 mm²
    • Compared with Light: 4 times

A Heavy tip is twice the diameter of a Light tip but leaves four times the area. Contact depth adds to that. A deeper contact leaves a deeper mark, even at the same tip diameter.

Where each size belongs

  • The first ring of supports above the raft
    • Starting preset: Heavy
    • Why: Holds the whole part to the build plate
  • Heavy hollow shells and plinths, such as Jiraiya's toad sections or Rock Lee's plinth quarters
    • Starting preset: Heavy
    • Why: Large layers and real weight
  • The main body, limbs and large islands
    • Starting preset: Medium
    • Why: Holds weight with a mark you can sand
  • Fingers, hair tips, fine edges and small islands
    • Starting preset: Light or Mini
    • Why: Small marks where they show
  • Thin parts such as Frieza's tree stalks or the staff in NomNom's Moogle King Mog
    • Starting preset: Light or Mini, placed close together
    • Why: Many small tips spread the load
  • Islands smaller than a Light tip
    • Starting preset: none
    • Why: Lychee advises leaving them alone

J3D Tech adds a test for small islands: an island under 4 layers or smaller than your support tip is often better left unsupported. A support there can cause more damage than the island.

Put the marks where they will not show

Supports land on the side of the part that faces the build plate in the slicer. Turn that side toward a join, an underside, the back or the inside of a cloak. The display side should face away from the plate.

Joins are the best hiding place. On Tanuki's Anya Forger, the torso's neck goes into the underside of the head. A mark there is hidden once the figure is built.

Faces are the worst place. Turn a head so its supports land on the back of the skull or inside the neck.

When safety wins

Use heavier supports when a failed part costs more than extra sanding. That means heavy hollow parts, tall thin parts and parts with large layers.

NomNom's Jiraiya has several such parts. NOM_gama_blade_Supported.stl is a 125.4 mm blade, 9.2 mm thick at its widest. NOM_fxA_Supported.stl is 141.3 mm tall and 20.1 mm thick. Parts that long and narrow give the supports little area to hold, so check them closely.

J3D Tech's guide goes as far as saying that over 95% of print failures come from bad supports, not bad printer settings. Calibrate first, so you know which of the two you are looking at.

Why resin prints fail, by symptom helps sort a support failure from an exposure problem. How to remove supports from resin prints covers taking supports off and sanding the marks.

Videos

  • Lychee — "Q&A with Lychee Slicer: Scaling Pre-Supported 3D Models." Lychee's own channel answers questions on scaling presupported files. Watch on YouTube
  • Lychee — "You need to do this before scaling down a model! | Lychee Slicer Tips." A Lychee tip on what to do before you scale a part down. Watch on YouTube
  • I Print 3D minis — "Islands, so many islands! Wait I thought this file was supported already? Lychee Island in depth." A walkthrough of Lychee's island tools on a file that was supposed to be supported already. Watch on YouTube
  • Lychee — "Learn how to support fast a full figurine | Lychee Slicer Full Process." Lychee supports a whole figure from start to finish. Watch on YouTube
  • Polyworkshop, in English! — "Learn Lychee Slicer - Getting started with manual supports." An introduction to placing manual supports in Lychee. Watch on YouTube
  • Figure Feedback — "The 2025 Beginner's Guide to Lychee Slicer." A beginner's tour of Lychee Slicer as it stood in 2025. Watch on YouTube

Read

Sources