Cindy Aurum by 3Dmoonn - Kit Overview

3Dmoonn's Cindy Aurum stands on an octagonal plinth ringed with chrome exhaust pipes, a pipe wrench over her shoulder and a hand on her hip. A nine-part standard figure that the studio presupported, hollowed in part and test-printed, plus a small two-file bust. Reviewed from the files and renders.

Share
Full-length front view of a blonde mechanic in an orange cap and cropped yellow jacket, a pipe wrench over her shoulder, standing on an octagonal plinth ringed with chrome pipes.

Cindy Aurum from Final Fantasy XV, by 3Dmoonn. She stands on an octagonal plinth ringed with chrome exhaust pipes, a big pipe wrench resting over her right shoulder and her left hand on her hip, in the orange cap, cropped yellow jacket, denim cut-offs and tool belt. The notable thing about this kit is the presupported set: the studio says it printed every part with those supports, and it hollowed four of them.

I wrote this from the STL files and the studio's renders. I haven't printed it yet.

At a glance

  • Studio: 3Dmoonn
  • Character and source: Cindy Aurum, Final Fantasy XV (game)
  • Section: Fan art
  • Versions and sizes: Two versions. The standard figure is roughly 270 × 113 × 113 mm (H×W×L): about 270 mm from the bottom of the plinth to the top of the cap, with the 112.7 mm square plinth setting the width and depth. The bust is roughly 115 × 48 × 42 mm with the standard head on it; its own two files stack to 81.8 mm. 3Dmoonn gives no dimensions in the download, so these come from the STL bounding boxes and the renders.
  • Size note: The studio doesn't give an assembled height for this kit. The height here, about 9 to 12 inches, is my estimate from the STL files.
  • Parts per version: Standard: 9 raw STLs, or 9 presupported STLs. Bust: 2 STLs of its own, plus the two head parts from the standard version, and possibly arms.
  • Presupports: The standard version only. standard version/Pre support Cindy/ holds 9 STLs in STL/ and three Lychee scenes in LYS/. The bust's two files have no presupported copies.
  • Largest part and plate fit: Standard, raw: leg2.stl at 21.2 × 34.4 × 130.2 mm is the longest part, and base.stl is the heaviest. Everything fits Mars-class, the base only on edge, since at 112.7 mm square it is wider than the plate's 90 mm short side; flat, it fits Saturn-class. Standard, presupported: leg2.stl at 134.4 mm is the tallest file. base.stl is set up on a 112.6 × 105.8 mm footprint, which fits Saturn-class but is 15.8 mm too wide for a Mars-class plate. Bust: bust_normal_torso.stl at 48.2 × 41.7 × 49.8 mm; both files fit Mars-class.
  • Ratings (estimated): Standard, presupported files: Print 2/5, Assembly 3/5, Paint 4/5. Standard, raw files: Print 3/5, Assembly 3/5, Paint 4/5. Bust: Print 3/5, Assembly 2/5, Paint 4/5. Skill tag: advanced.
  • Status: files reviewed, not printed
  • Where to get the files: 3Dmoonn on Patreon and 3Dmoonn on Gumroad. Every render of the figure carries "june reward available on my patreon".

The model

Cindy stands square to the front on the top plate of the plinth, feet a little wider than her hips, both boots flat. Her right leg is straight and her left knee bends slightly. Her right arm comes up with the elbow out to the side and the gloved hand at her shoulder, gripping a large pipe wrench that rests back over the shoulder. From behind (4.png) the wrench's adjustable jaw sits across the back of her neck. Her left hand is on her hip, fingers spread over the bare skin just above the belt. Her head tips a little and she looks straight out at the viewer. It is a relaxed standing pose. The attitude comes from the wrench and the hand on the hip.

The identifying details are all there. An orange-red baseball cap with a round white badge on the front, lettered HAMMERHEAD and FULL SERVICE STATION, which is legible in 2.png. Wavy blonde hair to the shoulders, with a sweep of fringe and one strand falling between her eyes. Round teal goggles hanging at her collar. A cropped yellow jacket, denim cut-offs, a leather tool belt with a pouch on each hip, dark thigh-high stockings and white boots. Black grease smears on her face, stomach and thighs. The face is warm-toned and realistic, with amber-brown eyes, dark lashes and glossy coral lips closed in a slight smile. Her right cheek has a couple of grease smudges and her left cheek a longer streak running down to the jaw. She looks easy and confident.

Costume, item by item. The cap is orange-red with paler orange piping along the seams and the brim edge, and the badge has teal-blue detail around a small emblem. The jacket is yellow, cropped above the navel, with a ribbed knit hem, a silver zip that stops below the chest so the jacket hangs open over a low-cut pink top, and a stand collar with a rust-orange lining. Rust-orange panels cap the shoulders and run down the backs of the sleeves. There is a flap pocket with small silver hardware on each upper arm, and two thin pale stripes down the outside of her left sleeve. The goggles are glossy teal lenses in black frames on a black strap. The gloves are full-fingered charcoal leather work gloves with a paler strap at the wrist. The wrench is worn steel with a scratched, speckled handle. The shorts are faded blue denim with pale, frayed hems, worn low under a wide red-brown leather belt with scratches, belt loops, a large silver rectangular buckle and a silver hook at her left hip. On her right hip is a brown leather pouch with a diamond-quilted flap and a smaller stitched pocket on the front. On her left hip is a tall, narrow leather holster with criss-cross laces and rivets down the edges. The stockings are plum-black with a soft sheen, each with a narrow band and a silver buckle at the top on the outer thigh. The boots are cream-white, calf-high and slightly slouched, with a red-orange strap and buckle around each ankle and a chunky dark heel, seen in 4.png. Skin shows at the face, the chest, the whole midriff, and the thighs between the shorts and the stockings. There are oil splatters on the stomach around and above the navel, at her left hip under the glove, and one on each thigh, the bigger on the left.

The plinth is a two-tier octagon in dark, scuffed gunmetal, with big bolt heads around the lower rim and a lighter, scratched steel top plate that she stands on. Bent chrome pipes run in stacked loops around the front and sides under the top plate, like a car's exhaust headers, joined at the front by a dark rectangular block. At each side a cluster of upright pipes rises above the top plate, their open ends heat-tinted blue, violet and gold. The silhouette is narrow and tall. Her two elbows are the widest point of the figure, roughly 85 mm apart going by 1.png, and the pouches make a second wide point at the hips, 78.0 mm across in waist.stl. The wrench stays inside that outline. The plinth carries the footprint at 112.7 mm square, and she stands well inside it.

Versions and sizes

  • Standard, raw files (standard version/)
    • H × W × L (mm): roughly 270 × 113 × 113 (from the bounding boxes and renders)
    • Pieces: 9
    • Presupported (format): No; these are the unsupported files
  • Standard, presupported (standard version/Pre support Cindy/STL/)
    • H × W × L (mm): the same build
    • Pieces: 9
    • Presupported (format): Yes: 9 STLs and three Lychee scenes in LYS/
  • Bust (bust/)
    • H × W × L (mm): roughly 115 × 48 × 42 with the standard head (the two bust files stack to 81.8)
    • Pieces: 2 of its own, plus the two standard head parts, possibly arms
    • Presupported (format): No

The standard figure is one sculpt and one build. The raw and presupported folders are two ways to print it.

The presupported set suits most people. With a Saturn-class printer, every file goes on the plate as the studio set it up, and the studio says it printed them all that way. With a Mars-class printer, eight of the nine fit as supplied. The base doesn't, so you would re-orient and re-support that one part, or print the raw base your own way.

The raw set suits you if you want to place your own supports or hollow to your own wall thickness. It is also the easier route to fitting the base on a Mars-class plate, since you set its orientation from scratch.

The bust is a pedestal and a torso, base_bust.stl and bust_normal_torso.stl. There are no renders of it and no supports for it. There is no head or arm in the bust folder, so it appears to borrow the head from the standard version, and possibly an arm or both. It suits a small shelf, a quick print, or a painter who wants the face, cap and jacket without the legs and the plinth.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

Standard version, raw files

Nine STLs in standard version/. Sizes are X × Y × Z from the report, with Z as height in these files.

Figure

  • head1_pt1.stl: Head, face and hair, going by its 38.8 mm width, which matches the hair under the cap
    • Size (mm): 38.8 × 37.6 × 30.1
    • Notes: The studio prints it solid
  • head1_pt2.stl: Probably the cap; its 25.3 mm width matches the cap's crown in 2.png
    • Size (mm): 25.3 × 38.7 × 22.8
    • Notes: Thin brim edge; the studio hollows it
  • normal_torso.stl: Torso: jacket body, chest, pink top and goggles
    • Size (mm): 42.9 × 41.7 × 67.0
    • Notes: The studio hollows it
  • waist.stl: Hips: shorts, belt and both pouches; its 78.0 mm width is the pouch-to-pouch span
    • Size (mm): 78.0 × 38.6 × 56.0
    • Notes: Heaviest figure part; the studio hollows it
  • arm1.stl: Appears to be her left arm, the hand on the hip
    • Size (mm): 29.3 × 41.5 × 58.4
    • Notes: Spread gloved fingers meet the hip
  • arm2.stl: Appears to be her raised right arm; at 61.3 mm wide it is long enough to carry the wrench, which has no file of its own
    • Size (mm): 61.3 × 47.1 × 47.4
    • Notes: The wrench handle is long and thin
  • leg1.stl: One leg, thigh to boot
    • Size (mm): 32.9 × 44.1 × 127.5
    • Notes: Weight-bearing
  • leg2.stl: The other leg, thigh to boot
    • Size (mm): 21.2 × 34.4 × 130.2
    • Notes: Longest part; weight-bearing

Base and scene

  • base.stl: Octagonal plinth with the exhaust pipes
    • Size (mm): 112.7 × 112.7 × 41.6
    • Notes: Heaviest file; solid; wider than a Mars-class plate's short side when flat

There are no alternates in this folder, so the folder is one build.

None of these files is presupported. Two things about the folder. There is no separate file for the wrench or the goggles, so both are on other parts; the goggles look like part of the torso. And the presupported set lives inside this folder, in Pre support Cindy/, rather than beside it.

Standard version, presupported

Nine STLs in standard version/Pre support Cindy/STL/. Sizes are X × Y × Z from the report, with Z as height, since these are set up for the plate. The hollow and solid notes come from the studio's Read me first.txt.

Figure

  • head1_pt1.stl: Head, face and hair (see above)
    • Size (mm): 41.2 × 46.0 × 41.7
    • Notes: Solid
  • head1_pt2.stl: Probably the cap
    • Size (mm): 38.0 × 35.6 × 33.2
    • Notes: Hollow
  • normal_torso.stl: Torso
    • Size (mm): 56.1 × 63.5 × 65.0
    • Notes: Hollow
  • waist.stl: Hips, shorts, belt and pouches
    • Size (mm): 50.8 × 81.8 × 62.9
    • Notes: Hollow
  • arm1.stl: Hand-on-hip arm (see above)
    • Size (mm): 52.5 × 32.6 × 55.0
    • Notes: Solid
  • arm2.stl: Raised arm with the wrench (see above)
    • Size (mm): 40.2 × 74.9 × 54.2
    • Notes: Solid
  • leg1.stl: Leg
    • Size (mm): 41.8 × 32.4 × 133.1
    • Notes: Solid
  • leg2.stl: Leg
    • Size (mm): 32.2 × 49.7 × 134.4
    • Notes: Solid; tallest file, 40.6 mm under Mars-class height

Base and scene

  • base.stl: Plinth
    • Size (mm): 112.6 × 105.8 × 81.8
    • Notes: Hollow; stands 81.8 mm tall against the raw 41.6 mm, so it is lifted and probably tilted on its supports

The Lychee scenes. standard version/Pre support Cindy/LYS/ holds three: base.lys, arms and heads.lys, and normal_torso, waist and Legs.lys. Going by the names, that is one plate for the plinth, one for the two arms and two head parts, and one for the torso, waist and both legs.

What the read-me says. Read me first.txt sits in Pre support Cindy/. The studio says it printed all the parts with these presupports and the results were satisfactory, and that the scenes are set up as printed. It printed them on a Halot One and an Elegoo Saturn S (the file spells it "Eleggo"). It also says some files are hollow and some are not: the torso, waist, head1_pt2 and base are hollow, and the arms, legs and head1_pt1 are solid, which the file calls "massive".

Supports and hollowing. The files match the read-me part by part: the parts it calls hollow are hollowed in the presupported set, and the parts it calls solid carry only the studio's supports and rafts. The supports themselves are not small: most supported files stand a few millimetres taller than the raw part's longest side (leg1.stl 127.5 to 133.1 mm, leg2.stl 130.2 to 134.4 mm).

Anything odd. In this kit the presupported files keep the raw names exactly, underscores and all, so head1_pt1.stl is head1_pt1.stl in both folders. The kit folder also has a Visit my Patreon.url shortcut that points to 3Dmoonn on Patreon. I can't tell from the numbers whether the studio added drain holes to the hollow parts; open the scenes and look before slicing.

Bust

Two STLs in bust/. Sizes are X × Y × Z from the report, with Z as height.

Figure

  • bust_normal_torso.stl: Bust torso: chest and jacket, finished at the bottom to sit on the pedestal
    • Size (mm): 48.2 × 41.7 × 49.8
    • Notes: Solid; no presupports

Base and scene

  • base_bust.stl: Bust pedestal
    • Size (mm): 33.7 × 33.7 × 32.0
    • Notes: Solid; no presupports; narrower than the torso above it

Figure

  • head1_pt1.stl, head1_pt2.stl (borrowed from standard version/): Head and cap
    • Size (mm): as above
    • Notes: Needed; see the check under Versions and sizes
  • arm1.stl, arm2.stl (borrowed from standard version/): Arms
    • Size (mm): as above
    • Notes: Possibly; see the check under Versions and sizes

The bust torso is 41.7 mm deep, the same as the standard torso, but 17.2 mm shorter and 5.3 mm wider. It looks like the standard torso cut off higher up, with something extra at the sides. That could be the tops of the arms, which would bear on whether the arms go on. The hand-on-hip arm reaches down to a hip the bust doesn't have, so if any arm goes on, I'd expect it to be the raised one with the wrench. The pedestal is 33.7 mm square, so the torso overhangs it on every side.

Standard, presupported files, 2/5 (estimated). All nine parts come supported, in three Lychee scenes, and the studio says it printed every one of them this way with satisfactory results. The hollowing is done too: the base, waist, torso and head1_pt2.stl are hollow.

Plate fit is the one catch. Eight of the nine fit a Mars-class plate (143 × 90 × 175 mm) as set up. The tallest is leg2.stl at 134.4 mm, with 40.6 mm to spare, and waist.stl at 81.8 mm is the closest to the plate's 90 mm short side. The base is set up on a 112.6 × 105.8 mm footprint, 15.8 mm wider than that short side. The report counts it as fitting Mars-class, but only turned on its side, which the supports aren't built for. On a Mars-class printer, re-orient and re-support the base, or print the raw base your own way. On Saturn-class (219 × 123 × 250 mm) all nine fit as supplied.

The thin parts are few: the wrench handle, the glove fingers, the cap brim, the goggle strap, the belt hook, and the open ends of the upright pipes on the base. The legs are long and slim, 133 to 134 mm supported. Presupported, a few thin parts, everything fits Saturn-class flat: that is a 2. Every file read cleanly in the report.

Standard, raw files, 3/5 (estimated). Start from the raw files and the studio's work becomes yours. The base, waist and torso are solid and want hollowing and drain holes; those are the parts the studio chose to hollow, along with the cap. A hollowed base with an open underside is a cupped shell, so orient it to avoid suction. The base is 112.7 mm square: flat, it fits Saturn-class but not Mars-class, so on a Mars-class printer it goes on edge or tilted. Every other raw part fits Mars-class easily. The thin parts are the same as above, without the studio's supports under them. Hollowing without presupports and one part that only fits Saturn-class flat make it a 3.

Bust, 3/5 (estimated). Both files fit Mars-class, but neither is presupported. The torso is solid and I'd hollow it. The pedestal is small enough to print solid. If you take the head from the presupported standard set, those two parts are done for you. Hollowing and supporting the torso yourself makes it a 3.

Assembly difficulty

Standard, both file sets, 3/5 (estimated). Nine parts: two head parts, torso, waist, two arms, two legs and the base. The count alone would be a 2. Two things push it to a 3.

First, the legs are separate, and they carry everything. Each is about 130 mm long, and they have to land in the waist and on the base at the same time, both boots flat on the top plate. Above them sit the waist, the torso, the head and cap, and both arms. Dry-fit the legs, waist and base together before gluing anything, then pin each boot into the base and each leg into the waist.

Second, the joins on bare skin. The midriff and the thighs are smooth skin, and I can't see in the renders where the torso, waist and legs are cut. If a cut crosses the stomach or the thighs, it's a join on a visible smooth surface, and you fill and sand it. The neck should hide under the jacket collar and the goggles, and the shoulder joins under the rust-orange shoulder panels.

The arms each have a second contact point. The hip hand's fingers rest on the skin above the belt, and the wrench lies back across her shoulders behind the neck. Fit the raised arm with the head and cap in place, since the hair and the wrench meet there. The cap goes onto the head last. I can't see pegs or sockets in the renders.

Bust, 2/5 (estimated). The two bust files plus the two head parts make four pieces, or six if both arms go on. The neck join should sit inside the jacket collar, as on the full figure. The torso overhangs a 33.7 mm pedestal, so glue it centred and let it set before adding the head.

Paint difficulty

Standard, both file sets, 4/5 (estimated). Realistic skin across a good share of the front: face, chest, the whole midriff and the thighs. The face is the detailed part, with amber-brown eyes, dark lashes and glossy coral lips a few millimetres across.

Count the materials: orange-red cap, white badge, blonde hair, yellow jacket with rust-orange panels and pale stripes, pink top, teal goggles in black frames, charcoal leather gloves, a steel wrench, faded denim, red-brown leather belt and pouches, silver hardware, plum-black stockings, cream-white boots with red-orange straps, and gunmetal, steel and chrome on the base. That is well past four.

The freehand work is the grease and oil: smears on both cheeks and splatter across the stomach, hip and thighs. I can't tell from the renders whether the splatter is sculpted or paint only. The cap badge lettering is small. The quilting on one pouch and the lacing on the other look sculpted, so a wash and a drybrush do most of that. It stops short of a 5 because there is no glow or translucent effect, and the biggest smooth areas, the stockings and bare legs, take simple long gradients. The heat tint on the pipe ends is the one gradient effect, and it is small.

Bust, 4/5 (estimated). The same face, cap, hair, goggles, jacket and chest skin, without the legs, belt and plinth. The face is still where the work is. There is no render of the bust, so I can't say what the pedestal looks like painted.

Paint reference. From the studio's colored renders. They are lit with pink-magenta from one side and a cooler light from the other, so the jacket swings from lemon toward lime on the lit side and the skin and boots pick up pink; the back view in 4.png and the close-up in 2.png are the best guides to the base colors. Hair is golden blonde, honey in the recesses, with paler highlights. Skin is warm and lightly tanned, with a pink flush at the cheeks. Eyes are amber-brown with dark lashes; brows are fair. Lips are glossy coral-pink. The grease is flat black with ragged edges. The cap is orange-red with paler orange piping and a darker underside to the brim; the badge is white with teal-blue detail and dark lettering. The goggles are glossy teal lenses in black frames with a black strap. The jacket is yellow with a rust-orange collar lining, rust-orange shoulder panels down the backs of the sleeves, two thin cream stripes on the left sleeve, yellow ribbing at the hem and cuffs, and a silver zip. The top underneath is pink. The gloves are charcoal leather with a paler grey wrist strap. The wrench is worn steel grey, darker in the scratches on the handle. The shorts are faded mid-blue denim, paler at the frayed hems and seams. The belt is red-brown leather with pale scratches, a silver buckle and a silver hook. The quilted pouch is brown leather with a darker diamond quilt on the flap; the laced holster is red-brown leather with an orange-tan top edge, cream laces and metal rivets. The stockings are plum-black with a soft sheen, with dark bands and silver buckles at the tops. The boots are cream-white with red-orange ankle straps, silver buckles and dark heels and soles. On the base, the plinth is dark gunmetal with scratches and worn edges, the top plate a lighter scuffed steel, the bolt heads steel, the looped pipes polished chrome, and the open pipe ends a heat tint from gold through violet to blue.

Five studio images, in the studio's order. The first four are full-color renders of the standard figure on a wooden table in front of a blurred shop with a large 3Dmoonn sign and a potted plant. Each carries the 3Dmoonn logo with "june reward available on my patreon" at upper right and a footer with patreon.com/3Dmoonn and 3dmoonn.gumroad.com/. The fifth is a release banner. One render is a rear view, and there are no renders of the bust.

Full-length front view of a blonde mechanic in an orange cap and cropped yellow jacket, a pipe wrench over her shoulder, standing on an octagonal plinth ringed with chrome pipes.
Full-length front view, camera at about waist height, the figure square to the camera with pink light on her right side. It is the cleanest look at the whole composition: the stance, the wrench over the shoulder, both pouches, the stocking buckles and boot straps, and the front of the plinth with the looped chrome pipes, the dark block at center, the bolt heads, and the upright heat-tinted pipes at both sides.
Close-up of a blonde woman in an orange cap with a round badge, teal goggles at her neck and an open yellow jacket, grease smudged on her cheeks and stomach.
Close-up from the cap to the top of the thighs, front on, against a dark blurred background. The best look at the face and the small details: the HAMMERHEAD and FULL SERVICE STATION lettering on the cap badge, the amber eyes and grease smears, the teal goggles, the jacket's collar, shoulder panels, arm pockets, sleeve stripes and ribbed hem, the oil splatter on the stomach, the glove on the hip, the belt buckle and hook, and the quilting and lacing on the two pouches.
Three-quarter view of the mechanic figure from her right side, wrench raised over her shoulder, on a dark plinth with chrome exhaust pipes.
Full length, three-quarter view from her right front, camera a little lower than in 1.png. Her raised arm is nearest the camera, so it shows the angle of the wrench over her shoulder, the side of the jacket and the shoulder pocket, the depth of the figure, and the plinth's left side with its pipe cluster.
Rear view of the mechanic figure with a pipe wrench across the back of her shoulders, a cropped yellow jacket, denim shorts and white boots on a piped plinth.
Rear view, full length, camera at about hip height. The only back view: the back of the cap, the loose curls at the nape, the pipe wrench's adjustable jaw resting across the back of her neck, the plain yellow jacket back cropped above the waist, the back of the shorts and belt with the laced holster now on the left and the quilted pouch on the right, the stocking backs, the chunky dark boot heels, and the back of the plinth with its pipes.
Studio banner of four panels showing the studio's June figures and two release dates, with the mechanic figure second from left.
Studio release banner. A wide banner of four panels side by side. From left: an armoured figure in a T-visor helmet holding a sword up and a glowing blue disc, rising on a column of grey smoke from a round base, with the June reward text; this Cindy figure in the same front view as 1.png, also with the June reward text; a crouching figure with large black feathered wings, a dark strapped coat and a long gun in each hand on a dark rocky base, marked "release date 15/June"; and a drawn illustration, not a sculpt render, of a dark-haired woman with a long braid and a red headband in a white sleeveless martial-arts top with a brown sash, fists raised, marked "release date 20/June". It shows where this kit sits in the studio's June releases, with two stated release dates, and adds nothing new about this kit.