> ## Content Index
> Fetch the complete content index at: https://3d-printed-garage-kits.ghost.io/llms.txt
> Use this file to discover other available public pages before exploring further.

# How kits are rated here
- URL: https://3d-printed-garage-kits.ghost.io/how-kits-are-rated/
- Published: 2026-11-15T22:51:12.000Z
- Updated: 2026-11-15T22:51:12.000Z
- Description: What do the Print, Assembly and Paint ratings on a kit post mean? The full 1-to-5 anchors, a real kit at each level, and how the library's kits spread.
- Author: Rin Stout
- Tags: Guides, #Stage 5 fixed 2026-11-11

Every kit post rates the kit three times, from 1 (easiest) to 5 (hardest): Print, Assembly and Paint. Each level has a fixed set of signals, called an anchor, and this page publishes all 15 anchors in full. The skill tag on a kit post is the highest of the three ratings: beginner for 1–2, intermediate for 3, advanced for 4–5.

If you're new, the guide to building your first garage kit figure covers choosing a first kit.

## In this guide

- Three ratings and one skill tag
- The Print rating, 1 to 5
- The Assembly rating, 1 to 5
- The Paint rating, 1 to 5
- Estimated ratings and actual ratings
- What the ratings don't measure
- How the ratings spread across the library
- Watch and read next
- Sources

Sizes on this page are in millimetres (mm). 25.4 mm is 1 inch.

## Three ratings and one skill tag

Each rating answers one question about the kit.

- **Print**
  - The question it answers: How hard is it to print every part cleanly and in one piece?
- **Assembly**
  - The question it answers: How hard is it to join the printed parts cleanly and securely?
- **Paint**
  - The question it answers: How much does the studio's color scheme ask of the painter?

A rating describes the kit, not the reader. What a Paint 4 means for you depends on what you have painted before.

### Where the ratings appear

Each kit post has an "At a glance" box near the top. The box lists the Print, Assembly and Paint ratings as numbers out of 5\. Further down, the Print difficulty, Assembly difficulty and Paint difficulty sections give the reasons, with STL file names and sizes.

Kit posts are written from the studio's files and renders before I print the kit. So each rating is marked "(estimated)" until I print the kit.

### How the anchors work

An anchor is a short list of signals for one level. A signal is something you can check in the files or renders, such as a part size or a material.

A kit post names the signals it found and the parts that carry them. Sometimes a kit shows signals from two levels. Then the kit post says which signal decided the rating, and why.

### How the skill tag is set

The skill tag is the highest of the three ratings.

- Highest of the three ratings: **1 or 2**
  - Skill tag: beginner
- Highest of the three ratings: **3**
  - Skill tag: intermediate
- Highest of the three ratings: **4 or 5**
  - Skill tag: advanced

Here are three made-up rating sets, to show the arithmetic.

- Print: **2**
  - Assembly: 2
  - Paint: 2
  - Highest: 2
  - Skill tag: beginner
- Print: **1**
  - Assembly: 3
  - Paint: 2
  - Highest: 3
  - Skill tag: intermediate
- Print: **1**
  - Assembly: 1
  - Paint: 4
  - Highest: 4
  - Skill tag: advanced

The tag follows the hardest stage, because you have to get through every stage to finish the figure. A kit that prints and builds easily but asks for a realistic face is not a beginner kit.

### The two plate classes

The Print anchors measure parts against two plate sizes: a Mars-class plate (about 143 × 90 × 175 mm) and a Saturn-class plate (about 219 × 123 × 250 mm). The guide to [whether a part will fit your printer](https://3d-printed-garage-kits.ghost.io/will-it-fit-build-plate/) explains both classes and how a part is checked against them.

## The Print rating, 1 to 5

The Print rating looks at plate fit, presupports, thin parts, and heavy or cupped shapes. Presupported files are files the studio already added supports to. Supports are thin printed rods that hold a part while it prints.

- Level: **1**
  - Anchor: Small, chunky parts. All presupported. All fit a Mars-class plate.
  - Example kit: Vault Boy, Tanuki Figures
- Level: **2**
  - Anchor: Presupported. A few thin parts (rods, glasses, spikes). All fit a Saturn-class plate flat.
  - Example kit: Moogle King Mog, NomNom Figures
- Level: **3**
  - Anchor: Some parts need hollowing and drain holes if you skip the presupports; or thin freestanding parts (a sword, a fishing rod); or some parts only fit a Saturn-class plate.
  - Example kit: Rock Lee, Tanuki Figures
- Level: **4**
  - Anchor: Large flat or cupped surfaces that risk suction (a mushroom cap, a throne seat, a base slab); or very thin elements (flame wisps, candle flames, rope); or parts that must be tilted to fit a Saturn-class plate.
  - Example kit: Frieza, Chibi Station
- Level: **5**
  - Anchor: Parts larger than a Saturn-class plate in every flat orientation. No presupports for that version. Heavy hollow shells that need several drain holes and careful orientation.
  - Example kit: Aira Shiratori, Chibi Station

### Print 1: Vault Boy by Tanuki Figures

Vault Boy is one of only 2 kits rated Print 1\. The kit has three small, chunky parts. All three are presupported and fit a Mars-class plate with room to spare.

The largest file, `Body.stl`, is 49.7 × 89.0 × 65.0 mm raw. The studio's supported version is tilted to 86.7 × 61.8 × 100.0 mm, which still fits a Mars-class plate flat.

The one thin element is the thumb on the raised hand. The thumb is short and thick for a figure part, and presupported. The base is a flat disc, 54.6 mm across, lifted off the plate on supports. There are no cupped surfaces.

The other Print 1 kit is the presupported version of Anya Forger by Tanuki Figures. The raw version of the same kit rates a 3, as the section on estimated ratings shows.

### Print 2: Moogle King Mog by NomNom Figures

Every part of the Moogle King Mog kit is presupported and fits a Mars-class plate flat. The largest supported file, `NOM_Base Upward Clouds_Supported.stl`, is 68.5 × 32.8 × 61.9 mm.

The thin parts keep the kit from a 1:

- `King Moogle Staff.stl` is 40.0 mm long. The staff is a rod close to the width of a support tip.
- `Base Lace.stl` is spread thin over 58.6 × 49.1 mm. The lace is an open ring of ribbon that will flex on the plate.
- The two attendant bodies are tiny, with a bow, bowstring, arrowhead and sword blade.
- The pom stalks on the three heads and the crown are thin cylinders with a ball on top.

There are no large flat or cupped surfaces. The cloud mound is a lump, not a cup.

### Print 3: Rock Lee by Tanuki Figures

The Rock Lee split kit is presupported, and all 23 files fit a Saturn-class plate. All but one fit a Mars-class plate too. The exception is `Sand_7_SUP`, at 125.1 × 99.9 × 122.0 mm. A part that only fits Saturn-class is a level 3 signal.

Thin parts are the other level 3 signal. The sand tendrils taper to points. `Sand_4` is spread thin across a 29.4 × 67.4 × 74.0 mm box. The open right hand has thin raised fingers, and the hair has loose strands.

The studio hollowed the four plinth quarters, which are large solid parts in the raw files. Each quarter is a hollow block with a broad, flat top. The kit post says to check the drain holes and the angle in your slicer.

Jiraiya by NomNom Figures is a second Print 3, for the split, 75 mm and bust versions. All 47 split parts are presupported and fit a Mars-class plate. Thin freestanding parts raise the rating to 3\. `NOM_gama_blade_Supported.stl` is a 125.4 mm blade, 9.2 mm thick at its widest.

Hollowing removes the solid inside of a part and leaves a wall. A hollow print can trap resin inside, so a hollow part needs drain holes. Formlabs explains that [drain holes let resin and air out during printing, and let isopropyl alcohol (IPA) through during cleaning](https://formlabs.com/blog/how-to-hollow-out-3d-models/?ref=3d-printed-garage-kits.ghost.io). Lychee Slicer's [3D hollowing sets a wall thickness between 0.5 mm and 10.0 mm](https://docs.mango3d.io/doc/resin-documentation/hollow/hollowing-3d/?ref=3d-printed-garage-kits.ghost.io). The full method is in How to hollow resin prints.

### Print 4: Frieza by Chibi Station

Chibi Station ships the Frieza kit as raw STL files only, so you support every part yourself. Plate fit is not the problem. All 24 parts fit a Mars-class plate.

The Print 4 comes from very thin elements:

- The four water pieces are wavy sheets with pointed tips, much like flames. `water4.stl` is a thin sheet spread across an 81.3 × 29.6 × 61.6 mm box.
- The five trees are round crowns on thin stalks. The smallest, `tree3.stl`, is 7.7 × 23.1 × 8.0 mm.
- The horns taper to points at each end of the 96.9 mm head.
- The two arm gems are tiny.

The raw files are also solid, so the heavy parts need hollowing.

Large flat or cupped surfaces are the other common level 4 signal, because of suction. Suction is the vacuum a cupped shape forms against the release film at the bottom of the vat. Lychee's documentation says [suction cups form when a void in a model has no way for resin and air to escape](https://docs.mango3d.io/doc/resin-documentation/resin-holes/suction-cup-detector/?ref=3d-printed-garage-kits.ghost.io). Formlabs lists the results: [separation between printed layers, structural defects, warping and print failures](https://formlabs.com/support/Preventing-suction-cups-in-PreForm/?ref=3d-printed-garage-kits.ghost.io).

### Print 5: Aira Shiratori by Chibi Station

The hair decides the Aira Shiratori rating. `Chibi_Station_Aira_Hair.stl` is 152.2 × 181.2 × 125.2 mm (6.0 × 7.1 × 4.9 in). The shortest side is 125.2 mm. The short side of a Saturn-class plate is about 123 mm. So the hair overruns a Saturn-class plate in every flat orientation.

A tilted fit may work, because the hair is a loop of strands. The kit post marks that as a test for Lychee Slicer. Otherwise, the hair needs a larger printer or a cut.

The other two level 5 signals are there too. Aira ships as raw STL files only, with no presupports. The heavy parts are solid, `Head1.stl` among them, and that head is yours to hollow.

Yuki Tsukumo by Lion Realm rates Print 5 because of one part. `curse.stl` is 190.3 × 240.8 × 128.5 mm. Its smallest side is 5.5 mm wider than the short side of a Saturn-class plate, so the part has to be cut. The kit has presupports, but the studio's plates also run over Saturn-class, by 0.2 mm and 3.6 mm.

## The Assembly rating, 1 to 5

The Assembly rating looks at the part count, where the joins land, which parts hang or carry weight, and whether order matters.

- Level: **1**
  - Anchor: One or two pieces.
  - Example kit: Happy keycaps, NomNom Figures
- Level: **2**
  - Anchor: Up to about 8 pieces. Keyed pegs. Joins hidden in folds or under other parts.
  - Example kit: Satoru Gojo bust, Tanuki Figures
- Level: **3**
  - Anchor: 10–20 pieces; or at least one join on a visible smooth surface; or a large hanging piece (cape, hair) that needs holding while the glue sets.
  - Example kit: BlackRose, NomNom Figures
- Level: **4**
  - Anchor: 20 or more pieces. A base in several pieces that must line up. Thin freestanding elements that need pinning.
  - Example kit: Regina, 3Dmoonn
- Level: **5**
  - Anchor: 30 or more pieces; or a large kit with weight-bearing joints, where the order of assembly matters and pinning isn't optional.
  - Example kit: Danua, Moon Figures

Keyed pegs are pegs and sockets shaped so a part fits only one way. Pinning means drilling a hole in each of two parts and gluing a short metal rod across the join. The pin carries the load, so the join doesn't rely on glue alone. FauxHammer shows a simple way of [lining up the two holes when you pin](https://www.fauxhammer.com/tutorials/how-to-align-holes-when-pinning-miniatures-wargames-models/?ref=3d-printed-garage-kits.ghost.io). The full method is in How to assemble a garage kit figure.

### Assembly 1: Happy keycaps by NomNom Figures

Each Happy keycap is one piece. There is nothing to glue, pin or align. Assembly is pressing the cap onto a keyboard switch. Sand any support marks off the bottom rim so the cap sits level.

### Assembly 2: Satoru Gojo bust by Tanuki Figures

The Gojo bust has five parts per build: base, torso, hand, head and hair piece. The glasses make six. No part is large or heavy enough to need pinning.

The joins look easy to hide. The collar stands up to his chin, so the neck seam should sit inside it. The hand file includes the forearm, so that join should sit inside the cuff. The torso sits on the base post, under the bust. The hair piece joins among the strands.

### Assembly 3: BlackRose by NomNom Figures

BlackRose has fourteen parts, keyed, with one large hanging piece. Square pegs and sockets sit at the main joins, such as head to neck and boots to leg stubs. Those joins are hidden or sit on hard edges.

The sword sets the rating. The blade is 162.5 mm (6.4 in) long and stands on the base beside her. The handle is part of `R_arm.stl`, so the grip join carries the blade's weight. The kit post recommends a pin at the blade tip and a pin at the grip. The kit post also recommends a test fit of arm, torso and sword before you glue any of them.

Order matters too. The cloth panels hang from the belt, and the hip plates sit over them. So the order is legs, then cloth, then plates.

### Assembly 4: Regina by 3Dmoonn

The standard Regina version has 23 parts. Seven are base and scenery pieces that have to line up before the figure goes on. The panel, truss and vine sections stack tall, so a small error at the bottom shows at the top.

The figure itself is 13 pieces. The shotgun (`hand_12.stl`) is long and thin, attached at the wrist and leaning on the scenery. The kit post recommends a pin at the wrist.

### Assembly 5: Danua by Moon Figures

Danua has 31 pieces, and the render is the only guide to where they go. The count alone puts the kit at 5\. The joints add to that:

- The seated body (`Danua_23.stl`) rests on a column slab (`Danua_20.stl`) on a two-segment shaft (`Danua_28.stl`, `Danua_29.stl`). That stack carries the heaviest part in the kit.
- The hair mass (`Danua_30.stl`) is 93.8 mm wide and hangs out behind the figure with nothing under it.
- Four or five separate hair locks join into the hair mass.

Mecha Pharaoh by Hybris is a second Assembly 5\. Its 30 parts put it at the top of the scale on count alone, but the wings are the real reason. Two wings, each about 138 mm long, hang off a torso about 74 mm long, and the kit post recommends pinning them. The tail runs from the body to the base and has to go in before the wings.

### When the part count and the rating disagree

The part count is one signal, not the whole rating.

Rio Futaba by Moon Figures has fourteen pieces, which reads as a 3\. The kit post rates it 2, because of where the joins land. The legs meet the body under the skirt and coat. The shirt collar and coat lapels hide most of the neck join. The hair pieces join along strand lines.

Beta by Moon Figures has sixteen pieces, which also reads as a 3\. The kit post rates it 4\. The only contact between the figure and the rock is the tip of one stiletto heel, on `Beta_13.stl`. The whole figure, with its bow and cloak, sits above that heel. The kit post treats a brass pin through the heel as required.

## The Paint rating, 1 to 5

The Paint rating follows the studio's color scheme in the colored renders. The rating counts distinct materials and checks how much skin shows. It also checks the face, patterns, textures, translucent or glow effects, and large gradients.

- Level: **1**
  - Anchor: One or two flat colors. No face.
  - Example kit: No kit rated 1 yet
- Level: **2**
  - Anchor: A few flat colors with simple shading. A cartoon face, or no face.
  - Example kit: Rio Futaba, Moon Figures
- Level: **3**
  - Anchor: Realistic skin on some of the figure. One or two textures (fur, leather). Some small details.
  - Example kit: Rock Lee, Tanuki Figures
- Level: **4**
  - Anchor: Realistic face and skin across most of the figure. Four or more distinct materials. A pattern or freehand element.
  - Example kit: Akaza, Chibi Station
- Level: **5**
  - Anchor: Everything in level 4, plus translucent or glow effects (flames, neon, candlelight) or large smooth gradients, where any uneven blend shows.
  - Example kit: Rose, NomNom Figures

A few painting terms come up below. A paint wash is thin paint that settles into recesses. Drybrushing drags a nearly dry brush over raised detail, so only the high points take color. Freehand is detail painted with no sculpted edge to follow. Glazing builds color with thin, see-through layers. The full method is in How to paint garage kit figures and How to paint garage kit eyes and faces.

### Paint 1: no kit yet

As of 5 October 2026, no kit post is rated Paint 1\. The Paint 1 anchor needs one or two flat colors and no face. Almost every kit in the library is a character, and a character has a face.

A Paint 1 kit would be something like a logo plaque in one color, or a plain display stand. You would apply primer, then one or two flat colors. There would be no eyes, no skin and no shading plan.

### Paint 2: Rio Futaba by Moon Figures

Rio Futaba has about a dozen painted items in about ten colors. They include pale skin, ash-brown hair, a yellow scrunchie, a white coat, a red tie and a navy skirt.

That is more than the "four or more materials" in the Paint 4 anchor. But every color is flat and cel-shaded: flat color with simple shading, like animation. The skin is flat anime skin, not realistic skin. There are no patterns, no fur, no glow and no gradients.

The face usually decides the Paint rating on an anime figure. For Rio Futaba, the studio supplies the eyes as waterslide decals in `eyes_RioFutaba.psd`. You print the decals on decal paper, seal them and apply them. The hardest freehand job on the figure becomes a decal job.

So the number of colors does not set the Paint rating. The finish each color needs sets the rating.

### Paint 3: Rock Lee by Tanuki Figures

Rock Lee has many materials for his size. The figure has skin, glossy black hair, a green knit bodysuit, bandages, a crimson sash and striped orange leg warmers. The scene adds pale sand, glossy green tiles, gray rock and lettered weights.

The style keeps Rock Lee at 3\. The face is anime-flat, not realistic. Skin shows only on the face, the fingers and the toes.

The textures suit simple methods. The knit bodysuit and the grainy sand both take paint washes and drybrushing well. The leg-warmer stripes sit in sculpted grooves, so a dark paint wash finds them. The fine work is in the eyes and the small lettering.

### Paint 4: Akaza by Chibi Station

Akaza has far more than four materials. The figure has skin, blue markings, hair, a vest in two pinks plus black, rope, tassels, trousers, beads and eyes. The base adds dust, rocks and spike effects.

The pattern is the blue stripes. The stripes cover his face, neck, chest, back, arms, hands and feet. If the stripes are sculpted in relief, the job is careful line-following. If they are flat, the job is freehand across the whole figure. The kit post marks that as a check.

Akaza's face is a chibi face with stylized skin, not a realistic face. The eye work is still fine. Each gold iris holds a kanji (a Japanese character), and the whites carry blue veins. For Akaza, the materials count and the stripe pattern decide the Paint 4.

### Paint 5: Rose by NomNom Figures

Rose has a realistic face, with bare skin on the face, upper arms and neck. The face part is small: `head.stl` is 16 × 31 × 15 mm, so the eyes and lips are tiny. The materials include iridescent armor, black leather, a teal metal blade, gems and the wings.

The wings decide the 5\. The render shows a smooth shift from yellow-green to blue-green across a large area, with a translucent look. That is a large gradient over a textured surface. A translucent membrane means glazing, or printing the wings in clear resin. The armor adds a second gradient, a blue-violet sheen over purple-black on every plate.

Trish by 3Dmoonn is a second Paint 5\. Trish has realistic skin across the face, shoulders, arms and midriff. The scene has glowing orange runes, glowing eyes on stone faces, and amber stained glass that reads as translucent. Those glow and translucent effects make the 5.

## Estimated ratings and actual ratings

Every rating on a new kit post is an estimate from the files and the studio's renders. The kit post's status reads "files reviewed, not printed", and each rating carries "(estimated)".

### Where an estimate comes from

Each kit post builds its ratings from the download, in this order:

1. Measure every STL file's bounding box, and check the fit against both plate classes in every flat orientation.
2. Compare each raw STL file with its presupported file to see what the studio hollowed, without working out a resin figure for the post.
3. List which versions ship presupported, and in what format.
4. Count the parts in each version, from the folder.
5. Read the studio's renders for where joins land, what hangs, and every painted material.
6. Set each rating against the anchors, and write the reasons with part names and numbers.

Everything in an estimate can be checked against the download. Things the files can't show, such as whether a join is keyed, are marked as checks in the kit post.

### After printing: the review block

After I print a kit, the kit post gets a review block. The review block has print notes, assembly notes, paint notes, a verdict and my own photos. Each estimated rating is replaced with the actual rating.

### One kit, more than one rating

A rating belongs to a version, not to the whole download. A version is one size or format of a kit: raw or presupported, split or merged, full figure or bust. When versions differ, the kit post rates each version.

- **Anya Forger, Tanuki Figures**
  - Version: Presupported
  - Rating: Print 1
  - The reason in the kit post: Three chunky parts, all supported, all fit Mars-class. The studio hollowed the head.
- **Anya Forger, Tanuki Figures**
  - Version: Raw
  - Rating: Print 3
  - The reason in the kit post: No supports. The head is solid. You hollow the head and add drain holes.
- **Doctor Doom, Chibi Station**
  - Version: Split
  - Rating: Assembly 3
  - The reason in the kit post: Nine or ten parts, a large hanging cape that goes on before the head, and pins at the head and a boot.
- **Doctor Doom, Chibi Station**
  - Version: One-piece statue
  - Rating: Assembly 1
  - The reason in the kit post: One piece. Remove the supports and the figure is assembled.

For the raw Anya Forger head, the kit post suggests drain holes in the underside, where the torso's neck goes in. The join covers them.

The Jiraiya kit post shows the same thing across formats. The split, 75 mm and bust versions rate Print 3\. The semi-split version rates Print 5.

The Paint rating can depend on your color choice. The Chibi Station picture frame pack renders each frame in one charcoal gray. Painted to match, the pack rates Paint 2: a base coat, a dark paint wash and a drybrush. Painted in full character colors, the same pack rates Paint 3.

So read the rating for the version you plan to print and the scheme you plan to paint.

## What the ratings don't measure

The ratings measure difficulty in three stages. Several things a reader wants to know sit outside those stages.

### Whether you will love the figure

A Print 5 is not a better kit than a Print 2\. The ratings say nothing about the sculpt, the pose or the character.

The "The model" section of each kit post describes the figure from the renders. Use that section to decide whether you want the figure. Use the ratings to decide whether you are ready for it.

### Time

The ratings carry no hours. The Print rating says how hard the parts are, not how many plates they fill. The Jiraiya split set has 47 parts and rates Print 3, the same as Rock Lee with 23 files.

The At a glance box gives the part count and the largest part for each version. Use those numbers to plan your plates.

### Cost

The ratings don't track resin use, and kit posts don't estimate resin until I have sliced and printed the kit. To work out a kit's resin and its cost yourself, see [how to estimate how much resin a print uses](https://3d-printed-garage-kits.ghost.io/how-much-resin-does-a-3d-print-use/).

### Your printer

The Print rating uses the two fixed plate classes, not your printer. Current printers don't all match those classes.

Elegoo's own page doesn't show the Mars 5 Ultra's build volume, but [All3DP gives it as 153.36 × 77.76 × 165 mm](https://all3dp.com/4/elegoo-fully-reveals-mars-5-and-mars-5-ultra-3d-printers/?ref=3d-printed-garage-kits.ghost.io). That plate is wider than Mars-class, but narrower (77.76 mm against 90 mm) and shorter (165 mm against 175 mm).

Elegoo lists the [Saturn 4 Ultra 16K build volume as 211.68 × 118.37 × 220 mm](https://us.elegoo.com/products/saturn-4-ultra-16k-10inch-monochrome-lcd-resin-3d-printer?ref=3d-printed-garage-kits.ghost.io). That plate is smaller than Saturn-class on all three axes. A part that fits Saturn-class with a few millimetres to spare may not fit a Saturn 4 Ultra 16K.

So compare the largest-part line in the At a glance box with your own plate. On a plate larger than Saturn-class, the size signal may not apply to you. The other Print signals still do. For choosing a printer, see What size resin printer you need for figures.

### Your skill

The ratings measure what the kit asks for, not what you can already do. A reader who airbrushes often will find a Paint 5 gradient easier than a first-time airbrush user. A reader who has never pinned a join will find Assembly 4 harder than the number suggests.

Your own choices also move the effective rating. Printing the presupported version can drop the Print rating, as Anya Forger shows. Eye decals and simpler color schemes lower the Paint work.

## How the ratings spread across the library

My kit library holds 519 kits from 18 studios. These are the kits I have, not everything each studio offers. As of 5 October 2026, 461 kit posts carry ratings. Percentages are rounded, so one rating's percentages may not add to exactly 100.

- Level: **1**
  - Print: 2 (0.4%)
  - Assembly: 19 (4.1%)
  - Paint: 0 (0%)
- Level: **2**
  - Print: 73 (15.8%)
  - Assembly: 50 (10.8%)
  - Paint: 12 (2.6%)
- Level: **3**
  - Print: 193 (41.9%)
  - Assembly: 154 (33.4%)
  - Paint: 134 (29.1%)
- Level: **4**
  - Print: 174 (37.7%)
  - Assembly: 189 (41.0%)
  - Paint: 254 (55.1%)
- Level: **5**
  - Print: 19 (4.1%)
  - Assembly: 49 (10.6%)
  - Paint: 61 (13.2%)
- Level: **Total**
  - Print: 461
  - Assembly: 461
  - Paint: 461
- **beginner**
  - Kit posts: 10
  - Share: 2.2%
- **intermediate**
  - Kit posts: 100
  - Share: 21.7%
- **advanced**
  - Kit posts: 351
  - Share: 76.1%

### Why most kits land at 3 and 4

Most kits are character figures with a costume, hair and a base. Those three things produce the signals for levels 3 and 4.

**Print.** 367 kits (79.6%) rate Print 3 or 4\. A Print 1 needs three things at once: small, chunky parts, presupports, and a Mars-class fit. Only 2 kits have all three. Hair strands, weapons and effects such as water or lightning are thin elements, which are signals for 3 and 4\. Raw-only kits also start higher, because their heavy parts need hollowing and drain holes.

**Assembly.** 343 kits (74.4%) rate Assembly 3 or 4\. Studios split a figure so the parts fit a plate and the seams fall along costume lines. A full figure with a scene base reaches 10–20 parts quickly. A base in several pieces, or a weapon that needs a pin, moves the kit to 4.

**Paint.** 388 kits (84.2%) rate Paint 3 or 4, and 315 kits (68.3%) rate Paint 4 or 5\. Two signals drive that: realistic skin, and four or more distinct materials. Skin, hair, one cloth and one metal already make four materials. Only 12 kits have the flat colors and simple face that a Paint 2 needs.

**Skill tag.** The skill tag takes the highest rating, so one 4 anywhere makes a kit advanced. Paint alone puts 315 kits at 4 or 5\. The other 36 advanced kits get there through Print or Assembly. A beginner tag needs all three ratings at 1 or 2, and only 10 kits qualify.

### What the spread means for a first kit

With only 10 beginner kits, most readers will start with an intermediate or advanced kit. So read the three ratings, not only the tag. A kit rated Print 2, Assembly 2 and Paint 4 is tagged advanced, but only the painting is hard.

If you would rather start with assembly and painting, a printed, unpainted kit from [the shop](https://store.3dprintedgaragekits.com/?ref=3d-printed-garage-kits.ghost.io) removes the Print stage. The shop ships in the US only.

The full guide to choosing and planning a first kit is How to build your first garage kit figure.

## Watch and read next

These go from first prints to advanced painting.

**Videos**

- **Bitzbox TV — "The ULTIMATE Beginners Guide To Resin 3D Printing."** A beginner's overview of resin printing, for readers before their first kit. [Watch on YouTube](https://www.youtube.com/watch?v=m-ePDHZ6dmQ&ref=3d-printed-garage-kits.ghost.io)
- **Groundeffected — "How To make Supports in Lychee Slicer for Resin Printing Large Scale Models."** Adding your own supports to large parts in Lychee Slicer, the skill every raw-only kit needs. [Watch on YouTube](https://www.youtube.com/watch?v=FdX%5FjHT9e4Y&ref=3d-printed-garage-kits.ghost.io)
- **Leona's Workshop — "Garage kit tutorial: Your first GK, sanding, fixing small broken parts & pinning."** Cleanup, small repairs and pinning on a first garage kit. [Watch on YouTube](https://www.youtube.com/watch?v=eqg79WLV6UI&ref=3d-printed-garage-kits.ghost.io)
- **Leona's Workshop — "Garage Kit Tutorial: Skin Tone and Shading for resin kits."** Skin color and shading on resin kits, the main step from Paint 2 to Paint 4\. [Watch on YouTube](https://www.youtube.com/watch?v=G9FEYQIU5kc&ref=3d-printed-garage-kits.ghost.io)
- **Those Gundam Guys — "Anime Resin Figure Building: Eyes and Face Painting."** Painting the face and eyes on an anime resin figure. [Watch on YouTube](https://www.youtube.com/watch?v=w94D9v66qyc&ref=3d-printed-garage-kits.ghost.io)
- **mokanaman — "Honing your airbrush skills 19: Painting garage kit anime figure."** Airbrush work on an anime garage kit, for the smooth gradients of Paint 5\. [Watch on YouTube](https://www.youtube.com/watch?v=ol%5FTcMd%5Fc7E&ref=3d-printed-garage-kits.ghost.io)

**Reading**

- [Hollowing 3D — Lychee Documentation](https://docs.mango3d.io/doc/resin-documentation/hollow/hollowing-3d/?ref=3d-printed-garage-kits.ghost.io). How Lychee Slicer hollows a part and sets the wall thickness.
- [Suction Cup Detector — Lychee Documentation](https://docs.mango3d.io/doc/resin-documentation/resin-holes/suction-cup-detector/?ref=3d-printed-garage-kits.ghost.io). How Lychee Slicer finds suction cups before you print.
- [How to Align Holes when Pinning Miniatures & Wargames Models — FauxHammer](https://www.fauxhammer.com/tutorials/how-to-align-holes-when-pinning-miniatures-wargames-models/?ref=3d-printed-garage-kits.ghost.io). A simple way to line up both pin holes across a join.
- [The Army Painter Academy: How to Paint Skin Tones — The Army Painter](https://thearmypainter.com/blogs/explore/the-army-painter-academy-skin-tones?ref=3d-printed-garage-kits.ghost.io). Base coat, paint wash and highlight steps for three skin tones.
- [How to paint eyes on your miniatures more easily — Tale of Painters](https://taleofpainters.com/2021/01/tutorial-how-to-paint-eyes-more-easily-on-your-miniatures/?ref=3d-printed-garage-kits.ghost.io). Painting the eyes before the skin, so you can correct them freely.

## Sources

- [Elegoo fully reveals Mars 5 and Mars 5 Ultra 3D printers — All3DP](https://all3dp.com/4/elegoo-fully-reveals-mars-5-and-mars-5-ultra-3d-printers/?ref=3d-printed-garage-kits.ghost.io)
- [Saturn 4 Ultra 16K — Elegoo](https://us.elegoo.com/products/saturn-4-ultra-16k-10inch-monochrome-lcd-resin-3d-printer?ref=3d-printed-garage-kits.ghost.io)
- [How to Hollow Out 3D Models With Meshmixer & PreForm to Save Material and Time — Formlabs](https://formlabs.com/blog/how-to-hollow-out-3d-models/?ref=3d-printed-garage-kits.ghost.io)
- [Preventing suction cups in PreForm — Formlabs](https://formlabs.com/support/Preventing-suction-cups-in-PreForm/?ref=3d-printed-garage-kits.ghost.io)
- [Hollowing 3D — Lychee Documentation (Mango3D)](https://docs.mango3d.io/doc/resin-documentation/hollow/hollowing-3d/?ref=3d-printed-garage-kits.ghost.io)
- [Suction Cup Detector — Lychee Documentation (Mango3D)](https://docs.mango3d.io/doc/resin-documentation/resin-holes/suction-cup-detector/?ref=3d-printed-garage-kits.ghost.io)
- [How to Align Holes when Pinning Miniatures & Wargames Models — FauxHammer](https://www.fauxhammer.com/tutorials/how-to-align-holes-when-pinning-miniatures-wargames-models/?ref=3d-printed-garage-kits.ghost.io)
- [The Army Painter Academy: How to Paint Skin Tones — The Army Painter](https://thearmypainter.com/blogs/explore/the-army-painter-academy-skin-tones?ref=3d-printed-garage-kits.ghost.io)
- [Tutorial: How to paint eyes on your miniatures more easily — Tale of Painters](https://taleofpainters.com/2021/01/tutorial-how-to-paint-eyes-more-easily-on-your-miniatures/?ref=3d-printed-garage-kits.ghost.io)